42 size list specifications dimensions t 1 in case of some problems for measured values, measure after applying rated voltage for 30 minutes at 105 c. (unit : mm) rv : rated voltage (sv) : surge (room temperature) t for the minimum packing quantity, please refer to page 51. 4 . specifications for each series sa series is miniaturized sc series with large capacitance. suitable for high frequency switching power supplies, etc. sleeve color : purple marking : polarity( ), rated voltage, rated capacitance (white) sanyo, os-con , lot.no. upper category temp.(105 c) 4 q f d j g j d b u j p o t g p s f b d i t f s j f t size code c d e f g h 6.3 6.3 8.0 10.0 12.5 16.0 d 0.5max. lmax. 7.8 10.8 11.5 11.5 23.0 26.0 0.45 0.60 0.60 0.60 0.80 0.80 0.5 0.5 0.8 0.8 0.8 0.8 0.5 0.5 0.8 0.8 0.8 0.8 2.5 0.5 2.5 0.5 3.5 0.5 5.0 0.5 5.0 1.0 7.5 1.0 f d 0.05 gmax. kmax. f g a' c k a b b' standards of terminal lead position sleeve d l 15min. 4min. 19min. d f mark ; ideal terminal lead position c; the middle point of a-a' 15 22 33 47 68 100 150 220 330 470 1000 2200 c e f h d f c d e f g h c c d e e f rv (sv) f 6.3 (7.2) 16 (18.4) 20 (23.0) 10 (11.5) sa series large capacitance and miniaturized products -55 c to +105 c m : 20% less than or equal to the value of table14 less than or equal to the value of table14 less than or equal to the value of table14 -55 c +105 c ? c/c tan leakage current ? c/c tan leakage current ? c/c tan leakage current z / z 20 c z / z 20 c 0.75 to 1.25 0.75 to 1.25 within 20% 1.5 times or less than an initial standard below an initial standard within 10% 1.5 times or less than an initial standard below an initial standard within 5% below an initial standard below an initial standard (after voltage processing) items characteristics endurance damp heat (steady state) resistance to soldering heat characteristics of impedance ratio at high temp. and low temp. conditions category temperature range tolerance on rated capacitance tangent of loss angle leakage current esr 120hz 120hz 105 c, 2,000h, rated voltage applied 60 c, 90 to 95%rh, 1,000h, no-applied voltage flow method (260 5 c x 10s) t 1 based the value at 100khz | +20 c after 2 minutes
43 table14 sa series characteristics list 20sa15m 20sa22m 16sa33m 6sa47m 20sa33m 16sa47m 10sa68m 20sa47m 20sa68m 16sa100m 6sa150m 20sa100m 16sa150m 10sa220m 6sa330m 16sa470m 16sa1000m 6sa2200m 20 20 16 6.3 20 16 10 20 20 16 6.3 20 16 10 6.3 16 16 6.3 15 22 33 47 33 47 68 47 68 100 150 100 150 220 330 470 1000 2200 90 70 70 60 70 60 50 40 36 30 30 30 28 27 25 20 15 15 1200 1300 1370 1430 1710 1830 2000 2450 2600 2740 2780 3210 3260 3370 3500 6080 9750 9750 0.06 0.06 0.06 0.07 0.06 0.06 0.07 0.06 0.06 0.06 0.07 0.06 0.06 0.07 0.07 0.08 0.09 0.13 6.00 8.80 10.56 5.92 13.20 15.04 13.60 18.80 27.20 32.00 18.90 40.00 48.00 44.00 41.58 300.80 640.00 554.40 t 1 tolerance on rated capacitance : m 20%, product ?? (tolerance on rated capacitance : 10%) is optionally available. however, the exception regarding g and h size. t 2 after 2 minutes t 3 100khz, +45 c c d e f g h temperature coefficient for allowable ripple current 4 t 1 rated voltage (v) rated capacitance ( ? t 3 tangent of loss angle (max.) leakage current ( t 2 4 q f d j g j d b u j p o t g p s f b d i t f s j f t ambient temp. coefficient tx ? 45 c 1 45 c ? tx ? 65 c 0.85 65 c ? tx ? 85 c 0.7 85 c ? tx ? 95 c 0.4 95 c ? tx ? 105 c 0.25 frequency coefficient for allowable ripple current 120hz ? f ? 1khz 0.05 1khz ? f ? 10khz 0.2 10khz ? f ? 100khz 0.5 100khz ? f ? 500khz 1 frequency coefficient
|
